ENREGISTREUR POUR SIGNAL NORMALISÉ  (16 000 mes.) pour transmetteurs etc..     : T-Logg 120 W

                           (avec fiche coudée pour intégration)

Plage de mesure                                 :    -1999 à 9999 points
                                                                   programmable
Virgule décimale                                 :     réglable
Signaux d'entrée                                : 1 seul choix possible !
                                                              0-1 V, 0-2 V, 0-10 V, 0-20 mA ou 4-20 mA
                                                              autre signaux d'entrée sur demande
                                                              (pas de sép. galv. entre l'entrée et l'interface)

ST-KO étui de protection

Flow Display H1O1 / H2O1

● No electrical supply required
● Individually calibrated display
● Compact design

Characteristics :
A piston fitted with a magnet is pushed through the medium against
the force of a spring. This activates the pointer of the measuring
device by means of a magnetic coupling. Because of the hermetic
separation from the medium, the display unit cannot be soiled by
the medium.

Ranges :
Details in the table correspond to horizontal inwards flow with
increasing flow rate.

Handling and Operation :
● Include straight calming section of 5 x DN in inlet and outlet.
● If the media are dirty, install a filter
(use magnetic filter for ferritic components)

Flow Switch FW1-...GM

● Economical design
● High switching power
● Insensitive to dirt

Characteristics :

Mechanical flow switch, for fluid media, with spring-supported
piston and magnetic triggering of a reed switch. Robust
construction in brass and POM.

Handling and Operation
Note
● Include straight calming section of 5 x DN in inlet and outlet
● Include a filter if the media are dirty (use magnetic filter for
ferritic components).
● It must be ensured that the values given for voltage, current,
and power are not exceeded.
● When switch on, a load must be connected in series.
● The electrical details apply to ohmic loads. Capacitive,
inductive and lamp loads must be operated using a protective
circuit.
Adjustment
Loosen screw slightly, push the switching head into the desired
position,

Mechanical flow switch, for fluid media, with magnetic triggering of a reed switch. Plastic housing with integrated filter.

● Adjusted switching value
● Integrated filter
● High switching power
● Optional flow limiter in the outlet piece

Handling and operation

● Include straight calming section of 5 x DN in inlet and outlet
● It must be ensured that the values given for voltage, current,
and power are not exceeded.
● When switch on, a load must be connected in series.
● The electrical details apply to ohmic loads. Capacitive,
inductive and lamp loads must be operated using a protective circuit.

● High switching power
● Compact design

Characteristics

Mechanical flow switch, for fluid or gaseous media, with
spring-supported piston and magnetic triggering of a reed switch.
Robust construction in brass or stainless steel.

Handling and Operation
Note
● Install straight calming section of 5 x DN in inlet and outlet.
● Include a filter if the media are dirty (use magnetic filter for
ferritic components).
● It must be ensured that the values given for voltage, current,
and power are not exceeded.
● When switch on, a load must be connected in series.
● The electrical details apply to ohmic loads. Capacitive,
inductive and lamp loads must be operated using a protective
circuit.

Adjustment
If it is necessary to set the switching value, the switching head can
be adjusted lengthways

Flow Switch MR1K

● High switching power
● Compact design

Characteristics :

Mechanical flow switch, for fluid or gaseous media, with
spring-supported piston and magnetic triggering of a reed switch.
Robust construction in brass or stainless steel.

Handling and Operation
Note
● Include straight calming section of 5 x DN in inlet and outlet
● Include a filter if the media are dirty (use magnetic filter for
ferritic components).
● It must be ensured that the values given for voltage, current,
and power are not exceeded.
● When switch on, a load must be connected in series.
● The electrical details apply to ohmic loads. Capacitive,
inductive and lamp loads must be operated using a protective circuit.

Adjustment
If it is necessary to set the switching value,
the switching head can be adjusted
lengthways.

Flow Transmitter /Switch FLEX-RT

● Versatile turbine flow sensor
● Switching output and analog output (4..20 mA / 0..10 V)
● Top quality materials
● Designed for industrial use
● Ingress protection IP 67
● Infinitely adjustably rotatable cable outlet for clean
alignment
● Small, compact construction
● Very simple installation

Characteristics :

A turbine acts as the primary sensor; its rotational speed is
proportional to the flow rate. The rotational speed is detected by
means of a biased Hall sensors, i.e. there are no magnets in the
flow space.
The FLEX transducer located on the sensor has an analog output
(4..20 mA or 0..10 V) and a switching output, which can be
configured as a limit switch for monitoring minimal or maximal, or
as a frequency output.

Flow Transmitter/Switch

● 4..20 mA output linearised
● 0..10V output linearised
● Frequency output proportional, linear
● Programmable through teaching
● LED for status display
● All metal housing
● Fully potted IP 67
● All parameters programmable via USB interface ECI-1

Characteristics
Mechanical flow switch, for oil, with spring-supported piston and
magnetic triggering of Hall sensors. Robust construction in brass or
stainless steel.
The LABO electronics make various output signals available:
● Analog signal 0/4...20 mA (LABO-HD2K-...I)
● Analog signal 0/2..10 V (LABO-HD2K-...U)
● Frequency signal (LABO-HD2K-...F) or
● A value signal Pulse / x Litres (LABO-HD2K-...C)
A model with switching output is also available.
If desired, the range end value can be set to the currently existing
flow using "teaching".

GIA 0420 WK - ex affichage embrochable auto-alimenté avec protection Ex pour les zones potentiellement explosives

GMR 110 la solution pratique pour le bois, le plâtre, la mesure de l'humidité de construction

Un appareil de mesure compact et robuste pour une détermination rapide de l'humidité des matériaux dans le

bois de chauffage et de sciage, l'aggloméré, le contreplaqué, le crépi, le plâtre, et bien d'autres encore.